Industrial Flooring

Heavy Duty Industrial Flooring System

Monneli Epofloor SC (IF)

Solvent-Free Trowable Epoxy Mortar (5.0 - 20mm) for Concrete Floor

Uses
Commercial and residential car parking
Workshops
Warehousing and storage facilities
Chemical and pharmaceutical factories
Food factories and slaughterhouses
back to Industrial Flooring
Technical Information
Product Description

EPOFLOOR SC (IF) is a solvent free trowable mortar for floors based on formulated epoxy resin, curing agents and silica sand specially selected for their ability to be applied and cured in ambient temperatures.

The system contains resin (Component A), hardener (Component B) and Graded Silica Sand (Component C).

Packaging, Coverage / Consumption

EPOFLOOR SC (IF) is supplied as a pre-measured kit depending on the customer’s requirements. Our standard packaging is 15 Liter kit.

EPOFLOOR SC (IF) contains resin (Component A), hardener (Component B) and sand pack (Component C):

  • EPOFLOOR SC (IF) resin (Component A) is a low viscosity standard coloured base which contains fillers and pigments.
  • EPOFLOOR SC (IF) hardener (Component B) is a low viscosity hardener which, after mixing with the base can be applied at 95% humidity and on damp floors. The hardener provides excellent chemical and abrasion resistance.
  • EPOFLOOR SC (IF) (Component C) is a graded low dusting silica sand.
Shelf Life & Storage

Keep in tightly closed containers and in sheltered and dry place with a temperature between +5°C and +35°C. In these conditions it maintains its characteristics unchanged for 12 months.

Technical Properties
Solid Content

100%

Kit Size

15 Liter

Theoretical Coverage

6 m2 at 6 mm

Pot Life at 18°C

90 minutes

Pot Life at 30°C

60 minutes

Mixing Ratio HARDENER : BASE : SAND (by weight

1.0 : 2.18 : 27.27

Mixed Density at 20°C

2.0 kg/L

Application Maximum Relative Humidity 95 % / Compressive Strength (ASTM C579)

95% / > 80 N / mm2

Bending Strength (ASTM C580)

> 25 N / mm2

Tensile Strength (ASTM C307)

> 14 N / mm2

Bond Strength to Concrete (ASTM D4541)

> 2.0 N / mm2

Application Information
Instructions for use

Application

Items Needed

  • Multi-speed drill fitted with a mixing paddle
  • Good quality medium haired non-shedding roller, suitable for epoxy application. Ensure that all loose hairs on the roller have been removed before use
  • 7” flat squeegee
  • Clean bucket, 2” brush and SOLVENTE 10 to clean the equipment

Method

Pour the mix onto the floor immediately and spread using the steel trowel. Wet the blade with SOLVENTE 10 to aid application. Apply at a thickness of 5-20mm.

Cleaning

Clean equipment with SOLVENTE 10. In case of spillage, use fine silica or cement to absorb the spill and dispose of according to local regulations.

Surface Preparation

The concrete must be at least 28 days old. The concrete must be free from loose matter, oil and dirt before starting surface preparation.

The best method to prepare the surface is dry grinding using a specialized planetary grinder. Before grinding, the surface must be free from any degreasing or cleaning chemicals which may have been used. At the end of grinding, the surface should be flat.

Surface irregularities and blow holes shall be repaired with EPOFINISH IF. When the filler is hardened, grinding and leveling of the patched area is recommended to ensure a good finish.

Ensure dust is removed from the surface using an industrial vacuum.

For best finish and adhesion, treat the surface with PRIMER POXY IF. In case the surface is very absorbent, apply a second coat of primer within the allowed recoating time.

Metal surface must be perfectly cleaned up to white metal by sand blasting. Application of PRIMER POXY IF should be done immediately before flash rusting occurs.

Additional Information
Health & Safety

Study the MSDS of the product before use or storage.

 

EPOFLOOR SC (IF) is not regulated per the ‘Directive 67/548/EEC EU Dangerous Materials List” so no special labeling is

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’sresponsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.06Mb)
OTHER PRODUCTS
More Products from this section
Monneli Epofinish IF

Solvent-Free Repair Mortar for Concrete Floors

Monneli Epofloor E 250 (IF)

Solvent-Free Epoxy Topcoat for Concrete Floors

Monneli Epofloor SL (IFT)

Solvent-Free Epoxy Self-Leveling Topping (2.0-4.0mm) for Concrete Floors

Monneli Uralevello

Medium Duty Polyurethane Hybrid Flooring

Monneli Uramassetto M1

Heavy Duty Polyurethane Hybrid Flooring System

RANDOM PRODUCT
Monneli Fugacolor

Water Repellant Anti-Fungus Tile Grout

Uses
As tile grout in hygienic environments including kitchens, bathrooms, shower stalls, swimming pools, steam rooms, restaurants, hospitals, clinics, etc.
As joint sealant from 2 - 20 mm of joint width. It is suitable for floors and walls joints internally and externally
Grouting for floors and walls in areas subject to intense traffic such as, airports, shopping malls, hotels, etc.
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map