Surface Treatment

Mould and Shutter Release Agents

Monneli Disarmante S

Solvent Based Mould and Shutter Release Agent

Uses
Plywood
Timber
Steel
back to Surface Treatment
Technical Information
Product Description

DISARMANTE S is a single component, solvent based mould and shutter release agent. It provides a chemical release action that is superior to that provided normal oil based release agents.

Advantages
  • Produces neat concrete surfaces by letting air and water bubbles rise freely during vibration
  • Ensures easy release, reducing damages and improving efficiency of production
  • Minimize surface stains and blemishes even with white cement
  • Suitable for use with virtually all types of formwork
Packaging, Coverage / Consumption

DISARMANTE S is supplied in 20 and 210 liter drums.

Coverage: Smooth, non-porous form surfaces 40 - 50 m²/liter

Shelf Life & Storage

DISARMANTE S has a minimum shelf life of 12 months when stored in unopened covered and dry place. Avoid exposing the drums to sunlight. Extreme temperatures cause the product to deteriorate.

Technical Properties
Appearance

liquid

Color

slightly amber

Physical Characteristics

very fluid, clear, non-oleaginous

Density at 25 °C

0.83 kg/L

Drying Time at 25 °C

> 60 minutes

Flash Point

Above 55°C

Temperature effect

Sustains temperature down to - 25 °C

Application Information
Instructions for use

Mould and Shutter Preparation

All mould and shutter surfaces must be cleaned from deposits of rust, concrete, oil and other materials.
It can be applied over fresh or old formwork.

Application

DISARMANTE S can be applied by brush, roller or mould oil sprayer. In most cases, spray application is recommended.

If mould oil sprayer is used, the nozzle is atomized to give a light and uniform coating. Excessive application should be avoided.

Non-absorbent surfaces require a single application. New, unsealed, timber surfaces should be recoated if delay in use of the mould leads to absorption of the release agent into the timber.

However, if DISARMANTE S is overly applied, excess materials should be allowed to drain and be carefully removed from the bottom of the mould by a cloth or sponge. Pools of DISARMANTE S should not be allowed to dry. Otherwise, surface retardation of the concrete will occur.

The surface should be re-coated depending on the porosity and texture of the mould surface.

After Stripping and Demoulding

The formwork and mould should be brushed or wiped clean of any excess dust prior to reapplication for the next use of the mould.

Repair of Moulds

After extensive use, surface of moulds will require repair. It should be cleaned of all residue and traces of DISARMANTE S to ensure proper adhesion of the repair material. The mould shall be cleaned by detergent followed by rinsing thoroughly with water.

Recommendation

Application should be done in thin layers.

Cleaning and Disposal

Spillage of DISARMANTE S should be absorbed into the earth or sand and transferred to appropriate containers. Practice caution in contaminated areas as the floors will become slippery.

Disposal of waste material should be in accordance with the local legislation under the guidance of the local waste regulatory authority.

Additional Information
Health & Safety

DISARMANTE W is a non-toxic material. However, inhalation of spray should be avoided and it is advisable to wear goggles when spraying. In case of eye contact, flush with water for few minutes. If irritation continues, consult a doctor. If product is ingested, do not induce vomiting, seek medical attention immediately.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.06Mb)
OTHER PRODUCTS
More Products from this section
Monneli Disarmante W

Water Based Mould and Shuttering Release Agent

RANDOM PRODUCT
Monneli Armaturea A1

Aromatic Pure Polyurea

Uses
Industrial Facilities
Cold Storage Facilities
Warehouse Floors
Below Grade Waterproofing
Parking Garage Decks
Water and Waste Water Treatment
Food Processing Facilities
Pulp and Paper Mills
Tank Linings
Pickup Truck Bedlining
Bottling & Canning Factories
Walkways and Balconies
Secondary Containment
Mining Operations
Landfill Containment
Bridge Deck Underlays
Water Parks & Theme Parks
Sprayed on Urethane Foam
Geotextile Linings
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map