Surface Treatment

Water Repellant Sealer

Monneli Idrosil XS

Solvent Based Silane-Siloxane Penetrating Water Repellant Treatment

Uses
Reinforce concrete structure
Cementitious substrate masonry
All types of structures including those in coastal environments
New and existing concrete
back to Surface Treatment
Technical Information
Product Description

IDROSIL XS is a single component penetrating Silane Siloxane treatment which penetrates into porous substrates and then reacts with moisture or pore water from the substrate to form a hydrophobic polysiloxane lining to the capillaries without clogging the pores or capillaries.

Advantages
  • Excellent penetration and water repellant characteristics
  • Protects surface from discoloration and weathering
  • Reduces water and chloride intrusion
  • Reduces efflorescence
  • Breathable; Allows interior moisture to escape without damaging the sealer
Packaging, Coverage / Consumption

IDROSIL XS is packed in 20 & 200 Liter Drums.

Coverage: 3-4m2/liter.

Shelf Life & Storage

Store under cover, out of direct sunlight and protect from extreme temperature. If properly stored, the product has a shelf life of 12 months from the date of manufacturing.

Technical Properties
Appearance

colorless liquid

Density at 25 °C

0.80 kg/L

Viscosity

9 cP

Flammability Point

40°C

Temperature of application

from +5ºC to +35ºC

Overcoating Time

Wet on wet application. Second coat can be applied immediately

Harmfulness according to EEC 88/379

Harmful for inhalation and contact

Application Information
Instructions for use

Pre-Application

Test a small area of the surface (generally 1.0m x 1.0m section) before starting application of the sealer to ensure desired performance results, aesthetics & coverage rate. Allow 5-7 days for the product to fully react.

Application

IDROSIL XS is a single component, applied at full strength and never diluted. Can be used directly from the container, no mixing is required but stir first before use.

Apply by brush, roller or low-pressure spray ensuring complete coverage at 3-4m2/liter.

On vertical surfaces, IDROSIL XS should be flooded starting at the bottom working steadily upward,

For aggressive contamination, it is preferable to slightly sand blast the surface. Algae growth, if exists, should be treated with recommended biocide.

When used as a protective impregnation, a minimum of two applications is recommended. Thus, apply the second coat is still wet.

Cleaning

Equipment and tools used should be cleaned with SOLVENTE 10 immediately after use.

Recommendation

  • Prolonged contact with air should be avoided
  • Containers should be sealed when not in use
  • Ensure adequate ventilation
Surface Preparation

All surfaces should be clean, sound and uncontaminated.

This preparation should leave an exposed concrete, free from dust, loose particles, deleterious matter, oil, grease, chemical films and other contaminants.

This is best achieved by lightly sandblasting the surface where moss, algae or similar growths have occurred. Treatment with a recommended biocide should be done after sandblasting process.

Additional Information
Health & Safety

IDROSIL XS should not be swallowed or come in contact with skin and eyes. Inhalation of spray should be avoided.

 

Wear protective clothing, goggles/masks and gloves during application.

 

Should accidental contact with skin take place, wash thoroughly with soap and water.

 

In case of contact with eyes, rinse with plenty and immediately seek medical advice.

 

If ingested, obtained medical attention immediately. Do not induce vomiting.

 

Avoid contact with skin and eyes. Use gloves and goggles during application. Ensure adequate ventilation and avoid inhalation of vapours.

 

Warnings

 

IDROSIL XS contains flammable solvents. All the precautions must be foreseen for use of such kind of products. For further information or particular use, contact our Technical Department.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.27Mb)
OTHER PRODUCTS
More Products from this section
Monneli Idrosil A

Water Repellant Penetrating Water Based Sealer

Monneli Idrosil L

Water Repellant Acrylic Sealer

RANDOM PRODUCT
Monneli Armaturea A1

Aromatic Pure Polyurea

Uses
Industrial Facilities
Cold Storage Facilities
Warehouse Floors
Below Grade Waterproofing
Parking Garage Decks
Water and Waste Water Treatment
Food Processing Facilities
Pulp and Paper Mills
Tank Linings
Pickup Truck Bedlining
Bottling & Canning Factories
Walkways and Balconies
Secondary Containment
Mining Operations
Landfill Containment
Bridge Deck Underlays
Water Parks & Theme Parks
Sprayed on Urethane Foam
Geotextile Linings
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map