Industrial Flooring

Cement Based Flooring Systems

Monneli Autolivellante ECO10

Self-Levelling Cementitious Mortar

Uses
AUTOLIVELLANTE ECO10 is used for smoothing and leveling surfaces with different thickness from 3 to 10 mm.
It is used for interior applications as screed on concrete for existing floors. It can be applied over existing ceramic, marble and natural stone floors.
back to Industrial Flooring
Technical Information
Product Description

AUTOLIVELLANTE ECO10 is a fine powder composed of cement, selected aggregates, additives and special synthetic resins. When mixed with water it forms a very fluid and flowing mixture, perfectly leveling, with easy application, and good adhesion to the substrate.

Advantages
  • Can be used internally on new or existing substrates
  • Flowable consistency for self-leveling application
  • Minimal shrinkage with good resistance to cracking
  • Good bonding strength
  • Good compressive and flexural strength
  • Economical and easy to use
Packaging, Coverage / Consumption

AUTOLIVELLANTE ECO10 is packed in 25 kg of bags

Consumption: 2.0 kg/m² per millimeter of thickness

Shelf Life & Storage

Keep the product in a dry covered place into original well closed packaging. Shelf life is 6 months from date of production if stored properly.

Technical Properties
Appearance

Grey Powder

Density at 25°C

2.0 kg/L

Working time of mixture at 25°C

30 minutes

Pull off bond strength

1.0 N / mm2

BRE Screed test (BS 8204 Pt.1)

0.6mm

VOC

2.0 g/L

Compressive Strength at 28 days (BS EN 13892)

>25N/mm2

Flexural Strength at 28 days(BS EN 13892)

>6 N/mm2

Tensile Strength (BS EN 13892)

> 0.5 N/mm2

Shrinkage Test (BS EN 13872)

1 mm/m

Initial setting time at 25°C

3 ½ hours

Final setting time at 25°C

5 hours

Time to wait before tiles laying

48 hours

Service Temperature

+5°C to +80°C

Application Information
Instructions for use

Priming

The substrate must be treated with Primer A18, a synthetic resin high penetrating primer. PRIMER A18 should be applied by brush or roller on to the cleaned surface area (particularly hidden surfaces) at a rate of 5-7m²/Liter.

The primer should be left to achieve a tack-free condition before applying the top coat. A second coat of primer may be required if the substrate is excessively porous.

Mixing

Pour into a container with 5.0-5.25 Liters of water the 25 Kg bag of AUTOLIVELLANTE ECO10. Mix with a low speed electric drill fitted with a suitable paddle for 2 minutes scraping sides and bottom of the can, until a uniform, lump free consistency mix is achieved. Allow the mix to stand for 3 minutes and then remix again for 1 minute.

Mix a quantity of product that can be applied within 30 minutes only. Do not remix with water if the mixture had already begun to set

Application

Pour the mixed product into the surface and spread to the desired thickness using flooring rake and a spike roller.

Protect the floor after leveling the mix from direct sunlight, high winds or rain.

AUTOLIVELLANTE ECO10 can be applied for thickness from 3mm up to 10 mm per layer.

It is possible to apply flooring material on top of AUTOLIVELLANTE ECO10 screed (such as ceramic, carpet, etc.) after nearly 48 hours from curing the product (depending on the thickness, the supports humidity and weather conditions).

Curing

Curing of the completed floor shall be carried out using a combination of damp hessian and polythene sheet for a period of no less than 2 days.

Cleaning

The product is self-leveling and requires minimal finishing or troweling operation. Clean tools and equipment with water before the material hardens.

Recommendations

  • Do not apply if the temperature is below +5ºC
  • During summer season or temperature higher than +35°C, working area should be covered to prevent the direct sun effects. Keep equipment cool and use cool water
  • Ground floor slabs on sloping gradient must incorporate a damp proof membrane in the sub-floor
  • It is advisable to use with cool water ( mix temperature should be +25ºC max.)
  • Protect the freshly applied AUTOLIVELLANTE ECO10 from direct sunlight and/or strong drying wind
  • AUTOLIVELLANTE ECO10 should not be applied over asphalt, weaker friable concrete, PVC tiles, or sheet substrates
  • AUTOLIVELLANTE ECO10 should not be applied over metal substrates
  • AUTOLIVELLANTE ECO10 should be cured for two days by covering with wet Hessian cloth and polythene sheet
Surface Preparation

The surface of the concrete to be prepared shall be sound, clean and uncontaminated.

This preparation shall be such as to leave a sound exposed concrete surface free from dust, loose particles and any deleterious matter. If the concrete surface is defective or has laitance, it must be cut back to a sound base. Excess laitance deposits should be removed by light mechanical scrabbling, grinding or grit/captive blasting followed by vacuum cleaning to pick-up dust debris.

All cracks and imperfections shall be repaired using BETOFINISH F, a cementitious fairing coat 0-3mm thickness.

New concrete floors should be allowed to cure for at least 28 days before applying the primer

Additional Information
Health & Safety

AUTOLIVELLANTE ECO10 can be harmful to skin as it contains cement powders which may releases alkalis when mixed with water.

During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.

In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.

If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updated on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.12Mb)
OTHER PRODUCTS
More Products from this section
Monneli Autolivellante 10

Self-Levelling Cementitious Mortar

Monneli Autolivellante 30

Self-Levelling Cementitious Mortar

Monneli Betolite

Light Weight Screed

Monneli Betolite*

LIGHT WEIGHT SCREED

Monneli Neocem Screed 100

Pre-mixed Floor Screed

view more
RANDOM PRODUCT
Monneli Epofloor HM

High Performance Epoxy Floor Screed

Uses
Food and Beverage Industry
Warehouses
Heavy engineering industrial floors
General repairs in floors subject to heavy traffic
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map