Concrete Repair

Injection Resin

Monneli Betothane 120

Rigid Polyurethane Injection Resin

Uses
BETOTHANE 120 is a fast reacting polyurethane foam that is mainly used to act as a waterstop for the sealing of leakages or to stop active water leaks with a flow and/or high hydrostatic pressure.
BETOTHANE 120 provides excellent adhesion to mineral construction materials such as concrete, bricks, metals and certain plastics.
back to Concrete Repair
Technical Information
Product Description

BETOTHANE 120 is a low viscosity, MDI-based water reactive polyurethane injection resin.It forms a rigid hydrophobic seal when in contact with water.

 

BETOTHANE 120 when in contact with water forms a carbon dioxide gas that produces a swelling pressure thus making the resin to expand into foam sealing all water penetration.

Advantages
  • Penetrates even in deep fine cracks
  • Does not shrink after curing
  • Excellent water sealer
  • The reaction speed can be controlled by varying the amount of catalyst
  • Forms a hard sealing with high strength in cracks or joints
  • Does not shrink, therefore volume stays the same
  • Excellent adhesion to concrete
  • Expands up to 2000%
  • Chemically resistant against water, weak acids and alkali, mineral oils, fungus and bacteria, ground water, sea water and petroleum products
Packaging, Coverage / Consumption

Packaging:

BETOTHANE 120 is supplied in two component kit:

  • 27KG in total (Part A and B).
Shelf Life & Storage

Storage:

Keep the product in dry and covered shed with a temperature between +10°C and +30°C.

If stored properly, BETOTHANE 120 has a shelf life of 12 months.

Technical Properties
PROPERTIES RESULTS
Appearance  Brown 
Mixing ratio (p.b.v.)  1.1
Density at 20°C (DIN 53 479)  1.13 kg/L 
Viscosity at 20°C (DIN 53 018)  200 ± 50 mPa.s 
Compressive strength (DIN EN 196 T1) Approx. 40 MPa
Slant shear strength (BS 6319, Part 4) Approx. 13.3 MPa
Flexural tensile strenth (DIN EN 196 T1) Approx. 3.5 MPa
Shore A hardness (ISO 868) Approx. 90
Volume expansion in  contact with water 1-10 times
Application time +6°C to 35°C
All values are subject to 5-10 % tolerance
Application Information
Instructions for use

Mixing

Mix Resin (Part A) and the Catalyst (Part B) thoroughly.  The components are mixed in the mixing head of a two-component injection-pump, using a suitable static mixer.

Because of the low viscosity, the resin will penetrate deep into the cracks. BETOTHANE 120 polymerizes into a rigid hydrophobic foam.

Cleaning
Clean the used tools with SOLVENTE 10 every time there is a need to stop the work for more than 15 minutes and immediately after completing the job and before the product dries.

Recommendation


BETOTHANE 120 could easily react with water or humidity in the air and forms CO2 gas that could build up pressure in the packaging that has been opened.

Additional Information
Health & Safety

Wear gloves, goggles to avoid any contact with eyes and skin. In case of contact in the eyes and skin, wash abundantly with warm water and consult a doctor. Ensure adequate ventilation at working place.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.25Mb)
OTHER PRODUCTS
More Products from this section
Monneli Betocryl 60

Three Component Acrylic Injection Resin

Monneli Betopoxy 200

Low Viscosity Epoxy Injection Resin

Monneli Betothane 100

Rigid Polyurethane Injection Resin

Monneli Betothane 150

Flexible Polyurethane Injection Resin

RANDOM PRODUCT
Monneli Cordoflex

Technical Polyethylene Foam Cord for Expansion Joints

Uses
CORDOFLEX is specifically formulated in order to provide a superior filling system for expansion and fractioning joints before elastic sealing in various areas such as:
Joints between walls and floors
Prefabricated concrete panels
Masonry and concrete
Window and door frames in both ceramic
Concrete floors and between standing finish and bearing structures
Connected products
Monneli Solvente 10

Thinner / Cleaning Solvent

Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map