Concrete Repair

Injection Resin

Monneli Betopoxy 200

Low Viscosity Epoxy Injection Resin

Uses
BETOPOXY 200 is used for the following:
Structural restoring
Consolidating of damaged concrete for beams, pillars,
Cement screeds cracks sealing
Vertical and oblique anchorage with high pull out resistance, etc.
Injecting into concrete and masonry cracks
To seal and bond cracks widths between 0.2 to 8 mm
back to Concrete Repair
Technical Information
Product Description

BETOPOXY 200 is a fluid epoxy resin, composed of two components that must be mixed before use. After mixing, BETOPOXY 200 transforms into a very fluid mixture that can be injected either with special equipment or by dropping in cracks and micro-cracks. It can also be used as an adhesive for grouting and structural gluing.

BETOPOXY 200 is solvent free and has good dielectric properties, which provides the steel reinforcement with cathodic protection.

Advantages
  • Resistant to chemicals
  • Very fluid which makes it suitable for injection in fine cracks
  • Superior adhesive to substrate
  • Impermeable
  • Solvent free
  • Non shrinkage product
  • High mechanical characteristics
  • Withstands hot weather conditions
  • Excellent adhesion to concrete, brick and masonry
Packaging, Coverage / Consumption

Packaging:

BETOPOXY 200 is supplied as 1 Liter and 4 Liter Kits.

 

Consumption:

1.1kg / 1 liter of cavity to fill.

Shelf Life & Storage

Storage:

It must be kept in dry sealed containers and in dry environment; in these conditions the product will have a shelf life of 12 months.

Technical Properties
PROPERTIES RESULTS
Appearance Liquid
Color Transparent to yellowish
Density at 25ºC  1.05 kg/L 
Pot life at 25ºC 90 minutes
Compressive strength at 7 days (ASTM C109) 90 N / mm² 
Flexure strength at 7 days 61 N / mm²
Tensile strength at 7 days 29 N / mm²
Bond Strength (BS 1881) > 2.5 N/ mm²
Thermal expansion coefficient 9.1 x 10-5 per °C
Complete curing 7 days
Temperature of application +5ºC to +35ºC
All values are subject to 5-10 % tolerance
Application Information
Instructions for use

Surface Preparation

The support must be perfectly dry, solid, free from inconsistent parts, dust, grease, etc.

Mortar and new concrete must be cured for at least 2 weeks.

Running water must be stopped by using suitable material like MUREX, a rapid setting water plug mortar.

Mixing

Pour component B (hardener) into component A (resin) and mix carefully, with an electric mixer until a homogeneous mixture is obtained.

Application

BETOPOXY 200 should be applied with standard injecting equipment having closed containers. The Injection Pressure should be at least 3 bar. Use injecting packers which must be inserted into predrilled holes along the length of the crack. The distance between packers depends on the crack’s width and depth.

After fixing packers use epoxy mortar to seal between packers to allow the resin to penetrate from one point to the next.

For crack injection, it is recommended to assign the job to an injection specialist. In case of partial mixing, maintain the proportions in volume.

For horizontal cracks pour the product directly. For ceiling and cracks bonding apply the product using a roller or brush.

Cleaning

Tools and equipment should be cleaned using SOLVENTE 10 immediately after use. Hardened material should be removed mechanically.

Recommendations

  • BETOPOXY 200 should not be used to fill moving cracks
  • BETOPOXY 200 should not be used if there is running water pressure, stop the running water by suitable material before the product is applied
Additional Information
Health & Safety

During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.

In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.

If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.25Mb)
OTHER PRODUCTS
More Products from this section
Monneli Betocryl 60

Three Component Acrylic Injection Resin

Monneli Betothane 100

Rigid Polyurethane Injection Resin

Monneli Betothane 120

Rigid Polyurethane Injection Resin

Monneli Betothane 150

Flexible Polyurethane Injection Resin

RANDOM PRODUCT
Monneli Dashbond SPX

Superior Quality Spatter Dash Bond Coating

Uses
DASHBOND SPX is specially formulated for application on fair face concrete containing micro-silica and on AAC (Autoclaved Aerated Concrete) blocks, without a need to hack the surface.
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map