Industrial Flooring

Fast Cure Flooring System

Monneli Epofinish FC

Fast Cure Solvent-Free Epoxy Repair Mortar for Concrete Floors

Uses
EPOFINISH FC is used in various installations such as:
Commercial and residential car parking
Workshops
Warehousing and storage facilities
Chemical and pharmaceutical factories
Food factories and slaughterhouses
General re-profiling over large areas
back to Industrial Flooring
Technical Information
Product Description

A solvent free repair mortar for floors based on formulated epoxy resin, curing agents and silica sand specially selected for their ability to be applied and cured in cold temperatures.

Packaging, Coverage / Consumption

Packaging:

EPOFINISH FC is supplied as a pre-measured kit depending on the customer’s requirements. Our standard packaging is 4 liter kit.

Shelf Life & Storage

Storage:

Keep in tightly closed containers and in sheltered and dry place with a temperature between 5°C and 35°C. In these conditions it maintains its characteristics unchanged for 12 months.

Technical Properties
PROPERTIES RESULTS
Solid content 100%
Kit size  4 Liter
Theoretical coverage   4 m² / 4 liter 
Pot Life at 7°C 80 minutes
Pot Life at 20°C 25 minutes
Thin layer (3mm) Dry tme at 7°C 15 hours
Thin layer (3mm) Dry tme at 25°C 2.5 hours
Mixing ratio HARDENER: BASE:  SAND (by weight) 0.36 : 1.00 : 6.65
Mixed density at 20°C 2.00 kg/L
Application maximum relative humidity 100%
Compressive strength (ASTM C579) >80.0 N / mm²
Bending strength (ASTM C580) >20.0 N / mm²
Tensile strength  (ASTM C307) 12.0 N / mm²
Bond strength to concrete (ASTM D4541) >2.0 N / mm²
Taber abrasion (ASTM D4060 CS17 Wheels) 60 mg loss / 1000 cycles
Water absorption  (ASTM D413 ) (maximum) 0.001%
Porosity with no sealer NACE Sand TM-01-74 0
Hardness shore D 85
All values are subject to 5-10% tolerance
Application Information
Instructions for use

Components

  • EPOFINISH FC contains Resin (Component A), Hardener (Component B) and graded sand (Component C).
  • EPOFINISH FC Resin (Component A) is a low viscosity standard coloured Base which contains fillers and pigments.
  • EPOFINISH FC Hardener (Component B) is a low viscosity and low color hardener which, after mixing with the resin can be applied at 100% humidity and on damp floors. The hardener provides excellent chemical and abrasion resistance.
  • EPOFINISH FC (Component C) is a graded low dusting silica sand.

Surface preparation

For best finish and adhesion, apply over PRIMER POXY FC.

The concrete must be at least 21 days old.  The concrete must be free from loose matter, oil and dirt before starting surface preparation.

The EPOFINISH FC is also designed for deep and wide cracks. The cracks should be opened up by sandblasting or mechanical wire brushing. Undercut if necessary.

Application

Items Needed

  • Multi-speed drill fitted with a mixing paddle
  • Hand held steel trowel
  • Clean bucket, steel trowel and SOLVENTE 10 to clean the equipment

Method

Using a drill and a paddle at low speed, stir the resin (Component A) for 1 minute.

Slowly add the Hardener (Component B) and increase mixing speed. Mix for 1 minute, ensuring proper mixing between the base and the hardener.

Slowly add the sand (Component C) and increase mixing speed. Mix for 2 minutes. Do not dump all the sand at once.

Pour the mix onto the floor immediately and spread using a steel trowel. Wet the blade with solvent to aid application.

Cleaning

Clean equipment with SOLVENTE 10. In case of spillage, use fine silica or cement to absorb the spill and dispose of according to local regulations.

Additional Information
Health & Safety

Study the MSDS of the product before use or storage.

 

EPOFINISH FC is not regulated per the “Directive 67/548/EEC EU Dangerous Materials List” so no special labeling is needed.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.28Mb)
OTHER PRODUCTS
More Products from this section
Monneli Epofloor FC

Fast Cure Solvent-Free Epoxy Topcoat for Concrete Floors

Monneli Epofloor SL (FC)

Fast Cure Solvent-Free Epoxy Self Leveling Topping (0.8 – 2.0mm) for Concrete Floors

Monneli Epofloor SL (FCT)

Fast Cure Solvent-Free Epoxy Self Leveling Topping (2.0-4.0mm) for Concrete Floors

RANDOM PRODUCT
Monneli Epozinc

Organic Zinc Rich Epoxy Primer

Uses
EPOZINC is a protection for steel reinforcement against corrosion when concrete repair is required.
It can be used for:
Repair of aged zinc rich or galvanized steel surface is required
Used as a protection primer in chemical process industries, refineries, ships, sewage plants and offshore structures
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map