Industrial Flooring

Epoxy Based Flooring Systems

Monneli Epofloor E100

Epoxy Floor Coating

Uses
EPOFLOOR E100 is suitable for the following:
Protection and decoration of interior floors in harsh environments
Workshops
Kitchens
Showrooms
Car park floors
back to Industrial Flooring
Technical Information
Product Description

A two component solvent based epoxy system suitable for floor coating. It forms smooth, semi-gloss, tough finish that has outstanding resistance to abrasion, chemicals, impact and spillage of solvent, fuel, diesel, oil, diluted acid and alkaline solutions. The product adheres perfectly to a variety of supports like concrete metal, wood, stoneware etc.

Advantages

n Chemical resistance

n Wide range of colours

n Durable and low maintenance

n Durable and hygienic finish

n High abrasion and mechanical resistance

Packaging, Coverage / Consumption

Packaging:

The product supplied in 4 and 15 Liter kits.

 

Consumption: 

6-7 m² / liter depending on substrate porosity.

Shelf Life & Storage

Storage:

Keep the product in tightly closed containers and in dry sheltered place.

 

Shelf life:

12 months from the manufacturing date if stored as recommended.

Colors
Refer Colmef color chart
Technical Properties
PROPERTIES RESULTS
Appearance  Liquid coating
Standard color  Refer Colmef color chart 
Density at 25⁰C  1.45 kg/L 
Solid content  85% 
Pot life 2 hours at 25°C
Bond strength (ASTM D4541) 2.0 N/mm² Concrete failure
Abrasion resistance  (ASTM D4060) 80 mg / 1000 cycles
Temperature of application +5°C to +35°C
Dry at touch  4 hours
Full traffic use 7 days at 25°C
Service temperature –5°C +80°C
Recommended DFT (per coat) 100-120µ
All values are subject to 5-10 % tolerance
Application Information
Instructions for use

Surface preparation

The surface of the concrete   shall be sound, clean and uncontaminated.  

This preparation shall be such as to leave a sound exposed concrete surface free from dust, loose particles and any deleterious matter. If the concrete surface is defective or has laitance, it must be cut back to a sound base.  
Excess laitance deposits are best removed by light mechanical scrabbling, grinding or grit/captive blasting followed by vacuum cleaning to remove dust debris.
Any blowholes, chipping or similar surface imperfections shall be repaired using EPOFINISH C, a solvent free epoxy resin repair mortar. Expansion joints shall be repaired using EPOMORT HS, a high strength solvent free epoxy mortar.
New concrete floors should be allowed to cure for at least 28 days before applying the primer.

Priming

EPOFLOOR E100 can be applied without the need of a primer. However, highly porous  must be treated with PRIMER POXY, a solvent based high performance Epoxy primer.

In that case the primer should be applied by brush or roller on to the cleaned surface area (particularly hidden surfaces) at a rate of 6-8 m2/Liter.

The primer should be left to achieve a tack-free condition before applying the top coat. A second coat of primer may be required if the substrate is excessively porous.

Mixing

EPOFLOOR E100 is supplied in two pre-weighed packs (Component A – Base and Component B – Hardener) which are ready for immediate in-situ use. Stir in both components before use.

Transfer the entire contents of component B (Hardener) into the component A (Base) can and mix with low speed drill and paddle (200 – 300 rpm) for 2 – 3 minutes till obtaining a mix with uniform consistency. Scrape the sides and bottom of the can during mixing to ensure homogeneity.

Application

Apply two coats of EPOFLOOR E100 with a roller, squeegee or airless spray to the primed tack free surface at a consumption rate of 6-7 m2/Liter.
Each coat will be a minimum of 100 microns thick. The second coat shall be applied after the first coat is completely dry.

The total dry film thickness of the coating shall be a minimum of 200 microns.

For anti-slip flooring, silica sand (with suitable size) can be broadcasted on first coat in order to achieve leatherette like finish. For heavy traffic areas such as drive lanes, ramps, turn areas, or other areas subjected to high abrasive traffic, apply a third coat of EPOFLOOR E100.

Cleaning

Tools and equipment should be cleaned with SOLVENTE 10 immediately after use. Spillages should be absorbed with sand or sawdust and disposed of in accordance with local regulations.

Recommendations

n The product must be handled with caution

n EPOFLOOR E100 should not be applied onto surfaces likely to suffer from rising damp or relative humidity >70%.

n EPOFLOOR E100 should not be applied at temperature below +5°C.

n EPOFLOOR E100 should not be applied to asphalt floors or PVC tiles.

Additional Information
Health & Safety

During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.
Ensure adequate ventilation at working place.

 

In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.

 

If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.30Mb)
OTHER PRODUCTS
More Products from this section
Monneli Epofloor E2000

High Build Solvent Free Epoxy Flooring System

Monneli Epofloor E240

SOLVENT FREE PERFORMANCE, HIGH BUILD EPOXY FLOORING SYSTEM

Monneli Epofloor E250

High Performance Epoxy Floor Coating

Monneli Epofloor ECT

Heavy Duty, Anti-Skid Surface Dressing

Monneli Epofloor HM

High Performance Epoxy Floor Screed

view more
RANDOM PRODUCT
Monneli Idrosil XS

Solvent Based Silane-Siloxane Penetrating Water Repellant Treatment

Uses
IDROSIL XS is used as a colourless surface protection for the following:
Reinforce concrete structure
Cementitious substrate masonry
All types of structures including those in coastal environments
New and existing concrete
Connected products
Monneli Epofinish C

Fairing Coat Solvent Free Epoxy Mortar

Monneli Epomort HS

High Performance Epoxy Mortar

Monneli Solvente 10

Thinner / Cleaning Solvent

Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map