Bitumen Waterproofing

Monneli Asfabit RBL +

Rubberized Bitumen Emulsion

Provides a sandwich membrane between screed flooring
A waterproofing coat for concrete foundations, bricks, retaining walls, etc.
It can be used to waterproof walls and floors in wet areas
For maintenance of many types of roofs including built up felt, aluminum, concrete, lightweight screed, timber, slate, asbestos, bitumen sheets, etc.
As a vapour/salt barrier for exterior walls to building facades behind granite, marble, stone, cladding, curtain walls, etc.
Can be used as adhesive for insulation boards and expanded polystyrene
back to Waterproofing
Technical Information
Product Description

ASFABIT RBL+ is a cold applied rubberized bitumen emulsion in dark brown color that, when dries, it forms tough black seamless and flexible coating.

  • Economical
  • Water based with excellent adhesion
  • Nonflammable
  • Easily applied by brush or squeegee.
  • Excellent resistant to alkalis, mild acids, chlorine
  • Compatible with all bituminous products
  • Resistant to chlorides and sulfates
Compiliance Standard
  • ASTM D 1187, D 2939
  • BS 8102
Packaging, Coverage / Consumption

ASFABIT RBL+ is packed in 200 Liter Drums

Consumption: 2 to 4 m² / liter

Shelf Life & Storage

Should be stored under cover away from extreme heat or direct sunlight or frost. Shelf life is 12 months in tightly sealed containers if stored properly.

Technical Properties

Dark brown dries to seamless black coating

Density at 25⁰C

1.0 kg/L


30.0 g/L

Solid content

40% ± 2%

Rubber content

≥  8%

Water resistance


Chloride resistance


Flash point


Application temperature

+5ºC to +35ºC

Service temperature

–5°C to +80°C

Application Information
Instructions for use


Hot, very dry or porous surfaces should be primed before applying ASFABIT RBL+.


ASFABIT RBL+ should be stirred before use until uniform color and consistency is achieved. Product is ready for use.


For waterproofing underground structures, the bituminous emulsion shall be applied by brush or squeegee at a maximum rate of 200 microns per coat.
The three coats must be applied at right angles to one another with a minimum of 6 hour intervals between each application at +25°C. Each coat must be completely dry before the next coat is applied.


ASFABIT RBL+ products should be removed from tools, equipment and mixers with clean water prior to the initial set. Cured material can only be removed mechanically.


  • Do not apply subsequent applications if the membrane is punctured or damaged
Surface Preparation

The surface of the concrete shall be sound, clean and uncontaminated.

This preparation shall be such as to leave a sound exposed concrete surface free from dust, loose particles and any deleterious matter. If the concrete surface is defective or has laitance, it must be cut back to a sound base.

Moss and lichen must be removed physically followed by treatment with fungicidal wash. After treatment, it must be washed down thoroughly with clean water and allow to dry.

Additional Information
Health & Safety

ASFABIT RBL+ is non-flammable, non-hazardous product. However, proper measures should be taken during work to avoid contact with eyes or skin. In the event of contact with eyes, wash immediately with clean water and seek medical care.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.06Mb)
More Products from this section
Monneli Asfabit

Cold Applied Bitumen Emulsion

Monneli Asfabit RB

Flexible, Rubberized Bitumen Emulsion

Monneli Asfabit RB+


Monneli Asfabit RBL


Monneli Betoboard

Protective Bituminous Board

view more
Monneli Betocure S

Water based concrete curing compound

Interior and Exterior Floor Slabs
Beams and Columns
Warehouse Flooring
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map