Industrial Flooring

Polyurethane Based Flooring Systems

Monneli Epofloor SLP25

Self leveling polyurethane floor topping

Uses
EPOFLOOR SLP 25 can be applied on mineral based substrates such as:
Concrete
Mortar
Epoxy modified cement mortars
Used as a broadcast floor topping for:
Warehouses
Cold storage facilities
Parking decks and ramps
Production and storage facilities
Chemical processing
Used as a self leveling broadcast floor topping for:
Industrial floors subjected to moderately
Heavy loading
Factory workshops
Production and storage areas
back to Industrial Flooring
Technical Information
Product Description

A solvent free, high performance three component pigmented self-leveling floor topping which provides a surface with excellent resistance to abrasion, chemical attack and other forms of physical aggression.  

 

Designed as self leveling polyurethane for use in concrete floors or steel substrates with thickness from 0.5 mm up to 2.5 mm. Has high filling ability when applied to concrete floors. Once cure, it provides a watertight seamless coating with uniform colour.

Advantages
  • Solvent free
  • Excellent adhesion to substrates
  • No seams or joints
  • Crack bridging
  • Flexible and durable
  • Easy to clean
  • Anti-slip when broadcast
  • Excellent abrasion and wear resistance
  • Resistant to impact and chemical attack
  • Available in a wide range of colors
Packaging, Coverage / Consumption

Packaging:

EPOFLOOR SLP25 is supplied in 15 Liter Kit.

 

Consumption: 

1 m²/Liter for 1 mm thickness depending on substrate condition.

Shelf Life & Storage

Storage:

Keep the product in dry and sheltered place at temperature between 0ºC and +35ºC.

 

Shelf life:

12 months if stored as recommended.

Colors
See standard color chart
Technical Properties
PROPERTIES RESULTS
Appearance  Liquid coating
Color  See standard color chart
Density at 25°C  1.5-1.6 kg /L 
VOC 8.0 g/L 
Solid content  100% 
Pot-life time at 25°C  40 minutes 
Shore D hardness 75
Tensile strength (ASTM C 307) 20 N/mm²
Compressive strength (ASTM C 579) 58 N / mm²
Flexural strength (ASTM C 580) 32 N/mm²
Elasticity module  (DIN 53-457) Approximately 1200 N/mm²
Chemical resistance Resistant to acid, alkalis, fuels, hydraulic oils and solvents
Open to foot traffic at 25°C 18 hours
Open to vehicular traffic at 25°C 24 hours
Completely hardened 3-5 days
Service temperature -5°C to +80°C
All values are subject to 5-10 % tolerance
Application Information
Instructions for use

Surface preparation

Support must be dry, compact, free of dust and other contaminating substances like oil, grease, etc. The humidity should not be greater than 75% at the time of application, and the moisture content of the substrate shall not be more than 5%. The pull-out resistance trial on the concrete screed must give a result non-inferior to 20 N / mm².

The right surface preparation will help to achieve the required adhesion strength between the substrate and the coating.

It is recommending to sand blast the substrate in order to guarantee a clean surface and to create a mechanical key between the substrate and the coating. Repair all the existing expansion joints using EPOMORT HS and be sure to follow the same joints through the new floor. Cracks should be treated using EPOFINISH. Use ARMOFLEX, a fiber glass mesh for moving cracks.

Priming

All surfaces must be treated with PRIMER PU, a solvent based epoxy primer. The primer should be applied by brush or roller on to the cleaned surface area (particularly hidden surfaces) at a rate of 6-8m²/Liter. The primer should be left to achieve a tack-free condition for 8-12 hours before applying the floor coating. A second coat of primer may be required if the substrate is excessively porous or use Primer Poxy FF, a solvent free epoxy primer.

Mixing

EPOFLOOR SLP25 is supplied in 3 pre weighed packs (Base, Hardener, graded filler, and colour pack) ready for immediate on site mixing. It is recommended that the kits, not be used partially unless suitable weighing equipment is available at site.

EPOFLOOR SLP25 must be mixed at the moment of use. The base (Component A) should be mixed for two minutes with a heavy duty, slow speed drill fitted with a mixing paddle at low number of turns (200-300 RPM) till obtaining a homogenous mix.  Pour the hardener (Component B) into the base mixture and mix for another two minutes. Add the filler (Component C) and mix until uniform consistency is achieved. Scrape the sides and bottom of the container during mixing to ensure homogeneity.

Application

Pour the mixed material onto the primed surface in pools or as a long strip. Using a trowel, pin screed, or notched trowel, spread EPOFLOOR SLP25 to the required thickness. To release entrapped air and assist with the smoothing operation, roll the material within 5 minutes after it is levelled, using spiked roller.

Allow to cure for minimum 18 hours at +25°C for light traffic.

Recommendations

n EPOFLOOR SLP25 should not be applied at temperatures below +100C and above +350C.

n EPOFLOOR SLP 25 should not be applied to asphalt, weak or friable concrete, PVC tiles or sheet substrates.

n Care should be taken to ensure that water does not come into contact with fresh EPOFLOOR SLP25 before full cure.

Additional Information
Health & Safety

During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary. In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly. If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.28Mb)
OTHER PRODUCTS
More Products from this section
Monneli Epofloor P1100

Seamless, Flexible, Polyurethane Flooring System

Monneli Epofloor P1140

Seamless, Polyurethane Traffic Deck Coating System

Monneli Epofloor P1150

Protective, Polyurethane Based Traffic Deck Coating System

Monneli Epofloor P1160

Waterproofing and Protective, Polyurethane Based Traffic Deck Coating System

Monneli Epofloor P1200

Waterproofing and Protective, Polyurethane Based Traffic Deck Coating System

view more
RANDOM PRODUCT
Monneli Elastoseal PU

Three Components Polyurethane Sealant

Uses
ELASTOSEAL PU is ideal for filling and sealing expansion joints at parking ramps, decks, pavements, precast joints, concrete bay joints, curtain walls, expansion wall joints, car parking slabs, industrial floors, warehouses and areas with forklift trucks movement, commercial and residential buildings, balconies, aircraft and cargo areas, exterior insulation walls, flexible seals around pipe work, manholes, basins, tanks and around swimming pool area (not immersed in water).
ELASTOSEAL PU is used on most kind of substrates such as; concrete, masonry, aluminum, brick, marble, granite, stucco, insulation walls and stone surfaces.
Connected products
Monneli Armoflex

Fibre Glass Reinforcing Mesh

Monneli Epofinish C

Fairing Coat Solvent Free Epoxy Mortar

Monneli Epomort HS

High Performance Epoxy Mortar

Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map