Synthetic Latex Additive for Cementitious Grout
GIUNTOLASTIC is an extremely elastic water based polymer. It is designed to be mixed with cementitious grout (NEOFIL COLOR or FUGACOLOR) in total or in partial replacement to water. The mixture of GIUNTOLASTIC with tile grout powder improves the compactness, abrasion resistance, impermeability and adhesion of grout when applied in joints between tiles.
In addition, the elastic property of the product allows the grout to absorb certain deformation and vibration on the substrates.
Packaging:
GIUNTOLASTIC is available in 20 Liter plastic pails.
Consumption:
Please refer to NEOFIL COLOR and FUGACOLOR data sheets.
Storage:
Store in dry and covered place out of direct sunlight and protect from high temperature (higher than +35ºC).
Shelf life:
12 months if stored as recommended.
PROPERTIES | RESULTS |
Appearance | White liquid |
Density at 25⁰C | 1.02 kg/L |
VOC | 1.0g/L |
Pot life time at 25⁰C | 60 minutes |
Mixture’s ratio with NEOFIL COLOR 0-4 | 30 : 100 |
Mixture’s ratio with NEOFIL COLOR 4-20 | 25 : 100 |
Mixture’s ratio with FUGACOLOR | 30 : 100 |
Harmfulness ECC 88/379 | No |
Temperature of application | +5⁰C to 35⁰C |
pH | 7 – 8 |
All values are subject to 5-10 % tolerance |
|
Surface preparation
The joints between tiles should be clean free of dust. Clean the joints between tiles and brush before grouting.
Mixing
Shake GIUNTOLASTIC pail before use. Pour a part of the latex as needed into a clean container and then add NEOFIL COLOR 0-4, NEOFIL COLOR 4-20 or FUGACOLOR. Mix to get a homogeneous paste free from lumps.
Application
Leave the mixture for about 10 minutes, then remix shortly and apply with a rubber grout float into the previously cleaned and wet joints.
Let the product set for about 20 minutes, and then proceed with cleaning the tiles with soft sponge. After the complete hardening of the grout, remove, with a dry sponge, all the remaining traces of grout on the surface. If the surface is still dirty clean it with PULINET. Read the instruction of PULINET in the technical data sheet before application.
Cleaning
Tools and equipment should be cleaned with water immediately after use.
NEOFIL COLOR mixed with GIUNTOLASTIC would perform as follows:
Properties | Result (0–4 mm) |
Result (4–20 mm) |
|
Density of the mix (kg./Lt.) | 1.80 | 1.90 | |
Flexural strength (N/mm²) | 7 | 7 | |
Compressive strength (N/mm²) | 30 | 30 | |
Water absorption (after 30 minutes) | < 5 g | < 5 g | |
Shrinkage (mm/m) | < 3 | < 3 | |
Temperature resistance | -30 to +80⁰C | -30 to +80⁰C |
Handle the product with caution.
During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.
In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.
If ingested, obtain medical attention immediately. Do not induce vomiting.
The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.
Water Repellant Anti-Fungus Tile Grout
Latex Modified Cementitious Tile Grout for Joints 0-4 mm Wide
Latex Modified Cementitious Tile Grout for Joints 4-20 mm Wide
Latex Modified Cementitious Tile Grout for Joints 4-20 mm Wide
Latex Modified Cementitious Tile Grout for Joints 0-4 mm Wide
Single Component Polyurethane Joint Sealant