Industrial Flooring

Primers

Monneli Primer Poxy (IF)

Penetrating Solvent-Free Epoxy Primer for Concrete Floors

Uses
PRIMER POXY (IF) prepares bare porous and nonporous concrete surfaces to be top coated with epoxy or polyurethane topcoats in various installations such as:
Commercial and residential car parking
Workshops
Warehousing and storage facilities
Chemical and pharmaceutical factories
Food factories and slaughterhouses
Schools and office buildings
back to Industrial Flooring
Technical Information
Product Description

PRIMER POXY (IF) is a solvent free primer based on formulated epoxy resin and curing agents specially selected for their ability to be applied and cured in warm temperatures, on dry or damp concrete.

 

Once the PRIMER POXY (IF) hardens, the concrete surface becomes much harder allowing application on weaker concrete possible.

Packaging, Coverage / Consumption

Packaging:

PRIMER POXY (IF) is supplied as a pre-measured kit depending on the customer’s requirements. Our standard packaging is 4 Liter and 15 Liter Kit.

Shelf Life & Storage

Storage:

Keep in tightly closed containers and in sheltered and dry place with a temperature between 5°C and 35°C. In these conditions it maintains its characteristics unchanged for 12 months.

Technical Properties
PROPERTIES RESULTS
Solid content  100%
Recommended DFT / coat  50-100 microns 
Kit size  4 Liters; 15 Liters
Theoretical coverage  150-300 m²/15 liter kit  
Pot life at 18°C 50 minutes
Pot life at 30°C 30 minutes
Thin film (75 µm) Dry time at 25°C 5-6 hours
Mixing ratio (by weight)  
Hardener: Base: 1.0:  1.67
Mixed density at 20°C 1.10 kg/L
Max recoat/ Topcoat time at 25°C 24 hours
Application maximum relative humidity 95%
Bond strength to concrete (ASTM D4541) >2.0N / mm²
Taber abrasion (ASTM D4060 CS17 wheels)  55mg loss / 1000 cycles
Water absorption (ASTM D413) (maximum) 0.001%
Porosity with no sealer NACE Sand TM-01-74 0
Hardness shore D 80
All values are subject to 5-10 % tolerance
Application Information
Instructions for use

Surface preparation

The concrete must be at least 28 days old. The concrete must be free from loose matter, oil and dirt before starting surface preparation.
The best method to prepare the surface is dry grinding using a specialized planetary grinder. Before grinding, the surface must be free from any degreasing or cleaning chemicals which may be have been used. At the end of grinding, the surface should be flat.

Surface irregularities and blow holes shall be repaired with EPOFINISH IF. When the filler is hardened, grinding and leveling of the patched area is recommended to ensure a good finish. Ensure dust is removed from the surface using an industrial vacuum.

Application Thickness

A thickness of 50-100µm per coat is recommended. In case the concrete is very porous, you can apply a second coat of PRIMER POXY (IF).

Items Needed

n Multi-speed drill fitted with a mixing paddle.

n Good quality medium haired non-shedding roller, suitable for epoxy application. Ensure that all loose hairs on the roller have been removed before use.

n 7” flat squeegee.

n Clean bucket, 2” brush and SOLVENTE 10 to clean the equipment

Method

Using a drill and a paddle at low speed, stir the resin (Component A) for 1 minute.

Slowly add the hardener (Component B) and increase mixing speed. Mix for 3-4 minutes, ensuring proper mixing between the resin and the hardener components until a completely homogeneous mixture is obtained.

The best method to apply the mixed product is by pouring it over the prepared surface. Then using a flat squeegee spread the material uniformly over the surface and back roll it maintaining the recommended thickness. Using just the roller is also possible.

In case the surface is very absorbent, apply a second coat of primer within the allowed recoating time.

Cleaning

Clean equipment with SOLVENTE 10. In case of spillage, use fine silica or cement to absorb the spill and dispose of according to local regulations.

Additional Information
Health & Safety

Study the MSDS of the product before use or storage.

PRIMER POXY (IF) is not regulated per the “Directive 67/548/EEC EU Dangerous Materials List” so no special labeling is needed

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.30Mb)
OTHER PRODUCTS
More Products from this section
Monneli Primer Poxy

Solvent Based Epoxy Primer

Monneli Primer Poxy (FC)

Fast Cure Solvent-Free Epoxy Primer for Concrete Floors

Monneli Primer Poxy FF

Solvent Free High Performance Epoxy Primer

Monneli Primer Poxy FF*

Solvent Free Epoxy Primer

Monneli Primer Poxy WB

Water Based Epoxy Primer

view more
RANDOM PRODUCT
Monneli Epofloor E240

SOLVENT FREE PERFORMANCE, HIGH BUILD EPOXY FLOORING SYSTEM

Uses
EPOFLOOR E240 is used for a variety of industrial applications such as:
Production assembly areas, workshops, dairies, bottling plants, breweries, pharma plants, kitchens, showrooms, etc.
Anti-slip floors, ramps & high traffic
Wet working areas
Floor coating for car-parking
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map