Tile Grouts

Epoxy Based Tile Grouts

Monneli Neofil PS

Polymeric Sand for Pavement Joints

Uses
NEOFIL PS can be used as replacement of existing joints and is recommended in variety of areas including the following:
Normal and high traffic areas
Strong slope surfaces
Pool sides or other frequently soaked surfaces
Terraces and patios
Walkways and driveways
Parking spaces
Pavements
back to Tile Grouts
Technical Information
Product Description

A unique mixture of high quality polymer binders and calibrated sand specially formulated to allow the pavement joints to expand and contract with the environmental elements such extreme heat, cold and freeze/thaw cycles.

Once NEOFIL PS sets, it becomes very firm and serves as a lock between the paver joints. This firm bond maintains paves securely in place and can be effective on both horizontal and sloped surfaces.

Advantages
  • Superior strength, creates a long term, semi-solid joint
  • Inhibits weed growth and deters insects
  • Prevents sand erosion caused by rain and other water run-off
  • Fast setting. Starts to set as soon as water is sprayed
  • Stabilizes pavers and strengthens interlocking
Packaging, Coverage / Consumption

Packaging:

The product is supplied in 25kg paper bags.

 

Coverage:

  Narrow Joints (m²) Wide Joints (m²) 
25 Kg   6.61 – 8.16  2.20 – 4.27

 

Joint Size:

  Narrow Joints (m²) Wide Joints (m²) 
Maximum Width 0.5 inch 1.0 inch
Minimum Depth 1.5 inch 1.25 inch

 

Quantity required depends on the shape and size of
paving area, the concrete pavers as well as the width of the joints.

Shelf Life & Storage

Storage:

Store in dry covered place and in original closed bags.

 

Shelf life:

12 months from production date if stored as recommended.

Technical Properties
PROPERTIES

RESULTS

Appearance

Powder

Adhesion strength (EN 1348)

1.40 N / mm²

Water absorptions

4.30%

All values are subject to 5-10 % tolerance

Application Information
Instructions for use

Surfaces preparation

All paver surfaces must be clean, sound, compact, free from dust, traces of oil, grease, mould release agent, curing compound and substances in order to prevent moisture from activating the polymer which could make sand stick to the surface and stain it.

Application

Spread NEOFIL PS uniformly over the surface. Using a push broom, sweep the product so as to fill the joints completely down to their full depth.

Make sure to avoid sweeping the product over long distances so that the integrity of polymeric joint is preserved.

Run a plate vibrator over the entire surface to fully firm up the joints. (It is necessary to check from the supplier about the suitability of applying a plate vibrator). On textural pavers, use a rubber mat to prevent scuffing the pavers.

Before wetting the surface, it is necessary to remove all excess sand with a leaf blower. All surfaces must be free of the product. This will avoid having product residue activated with water and stick to the surface of the pavers or slabs.

NEOFIL PS starts to repel water immediately after it gets wet. Ensure to wet maximum 200 sq. ft. of surface at a time. (Wetting large surfaces all at once takes too much time, NEOFIL PS will start to dry on the surface and will then be difficult to moisten properly). Ensure that the wetting of one section is finished before another section is started. Wetting of the entire project should be done without interruptions.

Set the spray nozzle to “shower’ and start showering from the bottom of the slope. Wet each section for approximately 30 seconds without dispatching the sand. Wet again the same section after approximately 30 seconds to make sure joints are completely wet.

Verify the progress of the wetness in the section using a small screw driver. The objective is to get joints wet 1 ½ inches deep. Immediately move on to an adjacent 200 sq. ft. section and repeat carefully the above procedure. Avoid flooding of the surface which could potentially cause unwanted water run-off.   

NEOFIL PS will become water resistant after 90 minutes and should not be exposed to rain within the specified period. To ensure optimal cohesion and long term stability, the product must be dried completely after initial wetting. Drying time will be shorter if the climate is warm and dry and longer if the weather is cool and damp. In cases where a surface jointed with NEOFIL PS could be exposed to water during the drying period, protect it with a tarp and immediately remove the tarp as soon as the risk of exposure is past. Temperature should remain above 32F during the entire drying process (minimum 48 hours).

Recommendations

  • Never apply NEOFIL PS to wet or damp surfaces since the bonding action will cause the product to stick to the surface instead of sliding properly into the joints
  • Do not use if rain is expected within 1 hour
  • Do not mix NEOFIL PS with cement or sand
  • Not for use on submerged or constantly wet surfaces
  • Do not use as a substitute for mortar (ex. Paving stones installed over a concrete bedding)
Additional Information
Health & Safety

NEOFIL PS can be harmful to skin as it contains cement powders which may releases alkalis when mixed with water.

 

During application, wear appropriate protective clothing, goggles, gloves and respiratory equipment if necessary.

 

In case of contact with skin, rinse with water and again wash thoroughly with soap and water. In case of contact with eyes, rinse with plenty of water and seek medical advice accordingly.

 

If ingested, obtain medical attention immediately. Do not induce vomiting.

Important note

The information in this Technical Data Sheet is based on Colmef Monneli’s experience. Colmef Monneli does not accept any liability arising from the use of its products as it has no direct or continuous control over where or how its products are applied. All Colmef Monneli’s Data Sheets are updates on regular basis. It is the user’s responsibility to obtain the latest version.

additional materials
Fast Download
Technical Properties Sheet
download (*.pdf 0.30Mb)
OTHER PRODUCTS
More Products from this section
Monneli Neofil Poxy

High Performance Epoxy Grout for Tiles

Monneli Neofil Poxy WB

Water Cleanable Epoxy Tile Grout

RANDOM PRODUCT
Monneli Espocem HES

High Early Strength Non Shrink Cementitious Grout

Uses
ESPOCEM HES is suitable for use precast concrete applications and for other structural sections of concrete where high early strength is required. Used for:
Machinery anchoring
Anchoring bolts of steel structures footings
Rigid filling of prefabricated elements
Underpinnings
Heavy duty support beneath machine base plates
Tie bar hole filling
Crane rails
Precast elements
Pile head treatment
Repairing and construction of degraded or damaged structural elements such as concrete beams, columns, walls, honeycombed concrete, floors and pillars
Repair of concrete pavements (roads, airports, industries), and rigid joints filling, up to 25 cm of thickness, in prefabricated residential and industrial building
Contact us
Choose a location
P.O. Box: 123808, Dubai
Toll: +971 4 8803488
Fax: +971 4 8803450
Site Map